Sep 08, 2018
Single Component Polyurethane Waterproof Coating with Nice Price Basic Info
Model NO.: SPU-301
Polyurethane Waterproofing Coating Method: Brush
Drying Method: Moisture Cured
Formation Mechanism: Conversion Type
Package: Iron Drum
Polyurethane Waterproofing Coating Transport Package: Pail
Main Raw Material: Polyurethane
Level: Finish Coat
Certification: None Voc
Polyurethane Waterproofing Coating Weigt: 20 Kgs
Specification: No VOC
HS Code: 32089010
Single Component Polyurethane Waterproof Coating with Nice Price Product Description
SPU-301H is a one component moisture-curing polyurethane waterproof coating especially used for horizontal plane. When this coating is applied on surface substrate, it has chemical reaction with the moisture in the air, and then it will form a seamless elastomeric rubber waterproof membrane.
Where to use
Subways in open cut method;
Kitchen or bathroom;
Floors, balcony and unexposed roofs;
Swimming pools, man-made fountain and other pools;
Top plate at plazas.
Single Component Polyurethane Waterproof Coating with Nice Price Advantages
Good tensile strength and elongation;
Both high and low temperature resistance;
Seamless, no pinholes and bubbles;
Resistance to long-term water erosion;
Corrosion-resisting and mould-resisting;
Convenient to apply.
ASTM C 836
Single Component Polyurethane Waterproof Coating with Nice Price Packaging
SPU-301H is sealed in 20kg or 22.5kg pails and transported in wooden cases. Each wooden case can be contained 36 pails of SPU-301H.
SPU-301H material should be stored by sealed pails at dry and well-ventilated places and protected from sun or rain. The temperature in stored places can not be higher than 40° C. It can not be closed to fire sources. The normal shelf life is 6 months.
SPU-301H is needed to be avoided sunshine and rain. Fire sources are forbidden during transportation.
The system is basically consisted of substrate, additional layer, waterproof coated membrane and protection layer.
1.7kg per m2 gives dft 1mm minimum. Coverage may vary with the substrate condition during application.
Surfaces should be dry, stable, clean, smooth, without pockmarks or honeycombs and free from any dusts, oil or loose particles. Cracks and surface irregularities need to be filled by sealants and do additional waterproofing. For smooth and stable surfaces, this step can be skipped.
Paint SPU-301H as additional layer to enhance at internal and external corners, drain pipes, floor drains or embedded parts.
Application of waterproof coated membrane
It can use rubber scrapers or spray equipments to paint 2 or 3 times. After fully dry, it can be painted again. The normal time between each painting is 24 hour. The direction of second time painting needs to be perpendicular to the first time painting.
Application of protection layer
After waterproof coated membrane is fully dry and meets quality requirements, it can begin application of protection layer.
The temperature for application of SPU-301H should be above 5 ° C.
SPU-301H needs to be consumed instantly and can not be diluted with solvent.
The storage and application places should be well-ventilated and no fire.
|Hardness||≥50||ASTM D 2240|
|Weight Loss||≤20%||ASTM C 1250|
|Low temperature crack bridging||No cracking||ASTM C 1305|
|Film thickness(vertical surface)||1.5mm±0.1mm||ASTM C 836|
|Adhesion-in-peel after water immersion||175N/m||ASTM C 794|
|Optional test after adhesion in peel||No separation at surface||ASTM C 836|
|Extensibility after hear aging||6.4mm (note 1) no cracking||ASTM C 1522|
|Stability||≥6 months||ASTM C 836|
Taitou Industrial Zone, Shouguang City, Shandong Province, China